Descriptions
2 Channel Position Controller (JPC)는 열악한 환경의 소형 설비의 위치제어를 위한 소형 컨트롤러이
다. Pulse input 2 Points, Analog Output (4~20mA) 2 Points 및 4 Digit BCD Output 1 Point 의 입출력
을 가지고 있다.
0.8 inch 4 Digit FND Display 2EA와 LCD (16* 2) Display를 통해 위치 표시 및 제어하며, 현장에서
Zero Position 설정이 용이하다.
Data Processor Specifications
1.Electrical Specifications
- Data Processor : 1 SET
- 16 *2 Digit LCD Display : 1EA
- 4Digit, 0.8Inch, FND : 2EA
- Signal Input : 2EA (Pulse Input)
- Key Switch Input : 3EA
- Push Button Input : 4 EA
- Analog Output :4~20mA 2 EA
- BCD Output : DC24V, 4 Digit
- Dip Switch Input : 1EA (8 Points)
- Power : AC110V/220V, 3A
2. Physical Specifications
- Dimensions (mm) : H250*W250*D110
- Weight (kg) : 3.5
3. Environmental Specifications
- Storage temperature: –25 to +85°C
- Operating temperature: 0 to 50°C
- Relative humidity: 5 to 95 % non-condensing
4. Power Supply
Input voltage range: AC110V/220V, 40W
CPU Specifications
- High performance RISC CPU
- Only 35 single word instructions to learn
- All single cycle instructions except for program branches which are two cycle
- Operating speed: DC - 20 MHz clock input
DC - 200 ns instruction cycle
- Up to 8K x 14 words of FLASH Program Memory,
Up to 368 x 8 bytes of Data Memory (RAM)
Up to 256 x 8 bytes of EEPROM Data Memory
- Interrupt capability (up to 14 sources)
- Eight level deep hardware stack
- Direct, indirect and relative addressing modes
- Power-on Reset (POR)
- Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
- Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
- Programmable code protection
- Power saving SLEEP mode
- Low power, high speed CMOS FLASH/EEPROM technology
- Fully static design
- In-Circuit Serial Programming. (ICSP) via two pins
- Single 5V In-Circuit Serial Programming capability
- In-Circuit Debugging via two pins
- Processor read/write access to program memory
- Wide operating voltage range: 2.0V to 5.5V
- High Sink/Source Current: 25 mA
- Commercial, Industrial and Extended temperature ranges
Signal Input Specifications
- Input Voltage : DC24V Max.
- Input Current : 2.5mA Max.
- Input Filter : 1mS
- Input Impedance : 12kΩ
- Normal Update Time : 0.1mS.
- Operating temperature : 0℃ ~ +70℃
- Storage Temperature Range : -10℃ ~ +85℃
Analog Output Specifications
- Normal Range : 4mA-20 mA (Current Output )
- Minimum Output : 0mA
- Maximum Output : 23mA
- Drive Capability : < 500 Ω
- 16-Bit Resoluton and Monotonicity
- ±0.012% Max Integral Nonlinearity
- ±0.05% Max Offset (Trimmable)
- ±0.15% Max Total Output Error (Trimmable)
- Loop Fault Detection
- 5 Reference (25 ppm/°C Max)
- Output Loop Compliance of 0 V to 12 V
- Update Time : 0.1m Sec
- Transient-Protected Outputs
- Read-back Threshhold : 2.5V
- Read-back Input Filter: 20㎲
- Update Time : 0.1m Sec
- Output Low
Current Sink Capability : 120mA Max
‘ON’ Resistance : 4 Ω Max
- Output High
Open Drain Voltage : 60V Max
Load current (A) : 500mA Max.
- Operating temperature : 0℃ ~ +70℃
- Storage Temperature Range : -10℃ ~ +85℃
BCD Output Specifications
Ordering Information
JPC-2-110/220
사용전원
Base Code